Hírek:

Az újonnan regisztrálók nézzék meg a spam mappában a megerősítő levelet!

Main Menu

GPU tuning (tweak)

Indította drizzt_do_urden, december 02, 2016, 05:15:35 DÉLUTÁN

Előző téma - Következő téma

0 Felhasználók és 11 Vendégek van a témában

sigisz

Koszi MACSI  a valaszod,


Hetvegen kiporbalom es ha meg netan valaki igy jart mint en   :(  itten talalhatoak megoldasok:


https://www.reddit.com/r/Amd/comments/3nxhju/my_semidetailed_guide_to_unbricking_an_amd_gpu/


netan ha valakinek mas otlete van azert aokat is szievsen elolvasom.

Zorg33

Ne az legyen az elsődleges kártya, úgy bootolj be.
Vagy B verzió, hogy a POST után de a win bootlás kezdete előtt adj áramot a kártyának és akkor bebootol a win és atiwinflash látni fogja.

sigisz

Kosz mindemkinek a valaszt. Sikerult megoldanom a problemat.Alaplapi videokartyat tettem elsodlegesnek biosbol igy elindult a windows es utanna ujraflasheltem a beteg karit. Midenkinek ajanlom hogy egyszerre csak egy karit flasheljen es utanna restart windows !!

evko81

#843
Hello!


R9 280X kártya bányászatra optimalizálásában tud valaki segíteni?
Lentebb kellene vinni a fogyasztását picit...
Milyen bios kell rá?


Köszönöm



ditibo

#844
Szerintetek mivel tudnám még a feszültséget alacsonyabbra állitani? Minden a minimumon van mégsem mozdul 1050 mV-ról lejebb.
http://www.kephost.com/images/2017/12/18/AB.jpg

Zorg33

Idézetet írta: ditibo Dátum december 18, 2017, 10:35:20 DÉLUTÁN
Szerintetek mivel tudnám még a feszültséget alacsonyabbra állitani? Minden a minimumon van mégsem mozdul 1050 mV-ról lejebb.
http://www.kephost.com/images/2017/12/18/AB.jpg


MIvel az AB nvidianal a csuszkán csak pozitívba tud offesetet állítani, ezért hiába huzigálod, undervoltolni nem lehet vele.
Viszont van neki a részletes feszültséggörbe editora, ha megnyomod a CTRL+F kombinációt.


karpy

üdv! msi p106-100 miner 6g kártyához hányas verziójú nvidia drivert és msi ab-t használjak? a legújabbakkal fagyogat nálam az ab. meg leáll a gpu cm-ba. köszi.

Dehogyis

Sziasztok!


Mi lehet az oka annak, hogy ha az Nvidia gtx1050ti 4 gb-nak MSI afterburner-ben felhúzom a Memory Clock-ját +800-900-ra (0-ról) akkor szépen lassan kb 15 perc alatt lefagy a gép. Eleinte csak lassul, aztán végül teljesen lefagy.


Előre is köszönöm ha valakinek van tippje.

Turcy086

Idézetet írta: Dehogyis Dátum január 14, 2018, 12:43:36 DÉLUTÁN
Sziasztok!


Mi lehet az oka annak, hogy ha az Nvidia gtx1050ti 4 gb-nak MSI afterburner-ben felhúzom a Memory Clock-ját +800-900-ra (0-ról) akkor szépen lassan kb 15 perc alatt lefagy a gép. Eleinte csak lassul, aztán végül teljesen lefagy.


Előre is köszönöm ha valakinek van tippje.

Túlhúzod. Ennyire egyszerű :)

Sthomi

Sziasztok!
Arra mi a megoldás ha a win10 nem ismeri fel AMD kártyaként az msi 580 rx-et. Ha illesztőprogit akarok cserélni az eszközkezelőben, akkor azt írja, hogy nem olvasható sérült, és minden marad a régiben.
Egyébként honnann tudom a jó illesztőprogit letölteni msi rx580 8gb kártyázok?

neoBp

Idézetet írta: drizzt_do_urden Dátum december 02, 2016, 05:47:06 DÉLUTÁN
GPU-Z -vel ne mentsetek BIOS -t mert csak 256 KB formatumba menti ki. Eredeti BIOS -nak 512 KB -na kell lennie. Garancia veszik hanem.
Atiflashel kell kimenteni az jo!


atiflash parancsok


Format: ATIFLASH [command] [parameter1] [parameter2] [parameter3] <option/s>
[command]:
-i [Num]                Display information of ATI adapters in the system.
                        Display information of adapter [Num] if specified.
-ai [Num]               Display advanced information of ATI adapters on system.
                        Display advanced information of adapter [Num]
                        if specified.
-biosfileinfo <File>    Displays the Bios info in file <file>
-p <Num> <File>         Write BIOS image in file <File> to flash ROM in Adapter
                        <Num>.
-pa <File>              Write BIOS image <File> to all appropriate adapters.
-s <Num> <File> [Size]  Save BIOS image from adapter <Num> to file <File>.
                        First [Size] kbytes (except for Theater in bytes) of ROM

                        content is saved if [Size] is specified.
-cf <File> [Size] [Sum] Calculate 16-bit checksum for file <File>.
                        Checksum for the first [Size] kbytes of the file is
                        calculated if [Size] is specified.
-cb <Num> [Size] [Sum]  Calculate 16-bit BIOS image checksum for adapter <Num>.
                        Checksum for the first [Size] kbytes of the ROM content
                        is calculated if [Size] is specified.
-mb <Num> <File>        Modify SSID, SVID, BIOS Pin Number, & Boot Message in
                        BIOS image of adapter <Num> to values in <filename>.
                        Input file example:
                           ssid = 715B
                           svid = 1002
                           biospn = "113-xxxxxx-xx"
                           bootmsg = "ATI graphic board"
-pak <File>             Package an executable for BIOS update according to
                        the commands in <File>.
                        Config file example:
                           outfile = update.exe
                           banner = "Update v1.0"
                           infile = a123.bin
                           command = -pa -padevid=715B infile
-isr <Num> <Build Number> <Board Number>  Set ISR number based on the given
                                          build and board number
                                          if not specified, print out ISR Number

-prod <Num> <12 digit serial number>      Set PROD number based
                                          on the given serial number
                                          if not specified, print out SN Number
-checkprodsn <Num> <12 Digit Serial Number>  Comparing the Prod SN based on
                                             existing prod sn saved in ROM
<option/s>:
-f              Force flashing regardless of security checkings (e.g. AsicID &
                BIOS file info check OR boot-up card).
-fa             Force flashing bypassing already-programmed check.
-fm             Force flashing bypassing BIOS memory config check.
-fs             Force flashing bypassing BIOS SSID check.
-fp             Force flashing bypassing BIOS P/N check.
-nw             No user interaction on test failure.
-sst            Use SST25VFxxx flashing algorithm regardless of ROMID straps.
-st             Use ST M25Pxx flashing algorithm regardless of ROMID straps.
-atmel          Use AT25Fxxx flashing algorithm regardless of ROMID straps.
-nopci          Do not enumerate PCI adapters, i.e. enumerate only AGP and
                PCIe adpaters
-pcionly        Enumerate only PCI adapters, i.e. do not enumerate AGP and
                PCIe adapters
-agp            Enumerate only AGP adapters, i.e. do not enumerate PCI and
                PCIe adapters unless used with -pcie or -pci
-noagp          Do not enumerate AGP adapters, i.e. enumerate only PCI and
                PCIe adpaters
-pcie           Enumerate only PCIe adapters, i.e. do not enumerate AGP and
                PCI adapters unless used with -agp or -pci
-nopcie         Do not enumerate PCIe adapters, i.e. enumerate only AGP and
                PCI adpaters
                PCIe adapters unless used with -agp or -pcie
-noremap        Skip BARs error detection and remapping in PCI configuration
                space
-reboot         Force a reboot of the system after successfully completing the
                specified operation
-keepisrsn      keep the ISR Number on the adapter when flashing a new VBIOS
-keepprodsn     keep the Prod SN on the adapter when flashing a new VBIOS
-siireset       Specifies the GPIO Pin to be used as the Reset when updating
                SiI1930 microcontroller firmware
                Input example:
                   -siireset=7 <No Spaces>
-siiuprog       Specifies the GPIO Pin to be used as the uprog when updating
                SiI1930 microcontroller firmware
                Input example:
                   -siiuprog=14 <No Spaces>
-scansii        Overrides normal adapter detection to enable detecting SSI
                roms with/without TPI firmware
-log            Logs output to atiflash.log, overrides existing file
-logappend      Logs and appends output to atiflash.log
-ddc            Enable DDC support
-padevid=<ID>   Use with -pa command to update adapters of specific device ID.
-passid=<ID>    Use with -pa command to update adapters of specific SSID.
-pasvid=<ID>    Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN>  Use with -pa command to update adapters of specific VBIOS PN.
-logappend      Logs and appends output to atiflash.log
-ddc            Enable DDC support
-padevid=<ID>   Use with -pa command to update adapters of specific device ID.
-passid=<ID>    Use with -pa command to update adapters of specific SSID.
-pasvid=<ID>    Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN>  Use with -pa command to update adapters of specific VBIOS PN.
-excl_memtrain_dtable     When flashing on new VBIOS, a pre-determined memory
                               training data table in the old VBIOS will not be
                          overwritten.
-isr <adapter num> [build num] [board num]     If build number and board number
                                               are specified, sets the ISR Number
                                               value in specified adapter.
                                               If only adapter is specified, the current
                                               ISR Number is displayed
-checkpn <adapter num> <filename>              Checks PN of the current product
                                               and compares it to external file
*<Num> = adapter number, <File> = filename
*[Size] = data block size in KBytes, except for Theater Pro in Bytes
*Use command -i to see the adapter numbers in the system.
*Theater Pro supports commands -i, p, s, cf, cr, t, v and options -f, -noremap.

Sajnos már megtörtént.
Sajnos már le mentettem a BIOS-t GPU-Z-vel 256kb formátumban.
Honnan tudom visszatenni az eredeti 512kb formátumu BIOSt ?
Köszönöm szépen a válaszokat  !


Sent from my iPhone using Tapatalk

Arkenso

Idézetet írta: neoBp Dátum február 10, 2018, 04:42:04 DÉLUTÁN
Idézetet írta: drizzt_do_urden Dátum december 02, 2016, 05:47:06 DÉLUTÁN
GPU-Z -vel ne mentsetek BIOS -t mert csak 256 KB formatumba menti ki. Eredeti BIOS -nak 512 KB -na kell lennie. Garancia veszik hanem.
Atiflashel kell kimenteni az jo!


atiflash parancsok


Format: ATIFLASH [command] [parameter1] [parameter2] [parameter3] <option/s>
[command]:
-i [Num]                Display information of ATI adapters in the system.
                        Display information of adapter [Num] if specified.
-ai [Num]               Display advanced information of ATI adapters on system.
                        Display advanced information of adapter [Num]
                        if specified.
-biosfileinfo <File>    Displays the Bios info in file <file>
-p <Num> <File>         Write BIOS image in file <File> to flash ROM in Adapter
                        <Num>.
-pa <File>              Write BIOS image <File> to all appropriate adapters.
-s <Num> <File> [Size]  Save BIOS image from adapter <Num> to file <File>.
                        First [Size] kbytes (except for Theater in bytes) of ROM

                        content is saved if [Size] is specified.
-cf <File> [Size] [Sum] Calculate 16-bit checksum for file <File>.
                        Checksum for the first [Size] kbytes of the file is
                        calculated if [Size] is specified.
-cb <Num> [Size] [Sum]  Calculate 16-bit BIOS image checksum for adapter <Num>.
                        Checksum for the first [Size] kbytes of the ROM content
                        is calculated if [Size] is specified.
-mb <Num> <File>        Modify SSID, SVID, BIOS Pin Number, & Boot Message in
                        BIOS image of adapter <Num> to values in <filename>.
                        Input file example:
                           ssid = 715B
                           svid = 1002
                           biospn = "113-xxxxxx-xx"
                           bootmsg = "ATI graphic board"
-pak <File>             Package an executable for BIOS update according to
                        the commands in <File>.
                        Config file example:
                           outfile = update.exe
                           banner = "Update v1.0"
                           infile = a123.bin
                           command = -pa -padevid=715B infile
-isr <Num> <Build Number> <Board Number>  Set ISR number based on the given
                                          build and board number
                                          if not specified, print out ISR Number

-prod <Num> <12 digit serial number>      Set PROD number based
                                          on the given serial number
                                          if not specified, print out SN Number
-checkprodsn <Num> <12 Digit Serial Number>  Comparing the Prod SN based on
                                             existing prod sn saved in ROM
<option/s>:
-f              Force flashing regardless of security checkings (e.g. AsicID &
                BIOS file info check OR boot-up card).
-fa             Force flashing bypassing already-programmed check.
-fm             Force flashing bypassing BIOS memory config check.
-fs             Force flashing bypassing BIOS SSID check.
-fp             Force flashing bypassing BIOS P/N check.
-nw             No user interaction on test failure.
-sst            Use SST25VFxxx flashing algorithm regardless of ROMID straps.
-st             Use ST M25Pxx flashing algorithm regardless of ROMID straps.
-atmel          Use AT25Fxxx flashing algorithm regardless of ROMID straps.
-nopci          Do not enumerate PCI adapters, i.e. enumerate only AGP and
                PCIe adpaters
-pcionly        Enumerate only PCI adapters, i.e. do not enumerate AGP and
                PCIe adapters
-agp            Enumerate only AGP adapters, i.e. do not enumerate PCI and
                PCIe adapters unless used with -pcie or -pci
-noagp          Do not enumerate AGP adapters, i.e. enumerate only PCI and
                PCIe adpaters
-pcie           Enumerate only PCIe adapters, i.e. do not enumerate AGP and
                PCI adapters unless used with -agp or -pci
-nopcie         Do not enumerate PCIe adapters, i.e. enumerate only AGP and
                PCI adpaters
                PCIe adapters unless used with -agp or -pcie
-noremap        Skip BARs error detection and remapping in PCI configuration
                space
-reboot         Force a reboot of the system after successfully completing the
                specified operation
-keepisrsn      keep the ISR Number on the adapter when flashing a new VBIOS
-keepprodsn     keep the Prod SN on the adapter when flashing a new VBIOS
-siireset       Specifies the GPIO Pin to be used as the Reset when updating
                SiI1930 microcontroller firmware
                Input example:
                   -siireset=7 <No Spaces>
-siiuprog       Specifies the GPIO Pin to be used as the uprog when updating
                SiI1930 microcontroller firmware
                Input example:
                   -siiuprog=14 <No Spaces>
-scansii        Overrides normal adapter detection to enable detecting SSI
                roms with/without TPI firmware
-log            Logs output to atiflash.log, overrides existing file
-logappend      Logs and appends output to atiflash.log
-ddc            Enable DDC support
-padevid=<ID>   Use with -pa command to update adapters of specific device ID.
-passid=<ID>    Use with -pa command to update adapters of specific SSID.
-pasvid=<ID>    Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN>  Use with -pa command to update adapters of specific VBIOS PN.
-logappend      Logs and appends output to atiflash.log
-ddc            Enable DDC support
-padevid=<ID>   Use with -pa command to update adapters of specific device ID.
-passid=<ID>    Use with -pa command to update adapters of specific SSID.
-pasvid=<ID>    Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN>  Use with -pa command to update adapters of specific VBIOS PN.
-excl_memtrain_dtable     When flashing on new VBIOS, a pre-determined memory
                               training data table in the old VBIOS will not be
                          overwritten.
-isr <adapter num> [build num] [board num]     If build number and board number
                                               are specified, sets the ISR Number
                                               value in specified adapter.
                                               If only adapter is specified, the current
                                               ISR Number is displayed
-checkpn <adapter num> <filename>              Checks PN of the current product
                                               and compares it to external file
*<Num> = adapter number, <File> = filename
*[Size] = data block size in KBytes, except for Theater Pro in Bytes
*Use command -i to see the adapter numbers in the system.
*Theater Pro supports commands -i, p, s, cf, cr, t, v and options -f, -noremap.

Sajnos már megtörtént.
Sajnos már le mentettem a BIOS-t GPU-Z-vel 256kb formátumban.
Honnan tudom visszatenni az eredeti 512kb formátumu BIOSt ?
Köszönöm szépen a válaszokat  !


Sent from my iPhone using Tapatalk

Az már megint hisztéria keltés :) Tökéletes az a 256 kb :) A másik 256 kb nullákkal van tele, azért nem menti a GPU-Z :)

neoBp


GPU-Z -vel ne mentsetek BIOS -t mert csak 256 KB formatumba menti ki. Eredeti BIOS -nak 512 KB -na kell lennie. Garancia veszik hanem.
Atiflashel kell kimenteni az jo!


atiflash parancsok


[/quote]

Sajnos már megtörtént.
Sajnos már le mentettem a BIOS-t GPU-Z-vel 256kb formátumban.
Honnan tudom visszatenni az eredeti 512kb formátumu BIOSt ?
Köszönöm szépen a válaszokat  !


Sent from my iPhone using Tapatalk
[/quote]

Az már megint hisztéria keltés :) Tökéletes az a 256 kb :) A másik 256 kb nullákkal van tele, azért nem menti a GPU-Z :)
[/quote]

Értem, köszönöm szépen !

bazsy

#853
Keresek Sapphire rx480 4gb Nitro+ OC micron ramos kártyához eredeti biost!
Ha létezik ilyen rammal szerelt kártya és valakinek van,akkor legyen szíves küldje el nekem az biost.



Tárgytalan!


zsombor1

RX560-as kártya.
Bios moddolva.
Eleinte kerestem itt a fórumon és a videósoknál is, hogy milyen értékeket állítsak be. Rájöttem, hogy ezt mindenkinek saját magának kell kitapasztalnia, hogy mit bír a kártyája. Elkezdtem szépen lassan emelni a Mhz-et, és 2040-ig jutottam el úgy, hogy nem fagyott le a gép. Ha már 2050-re emeltem, elkezdett vacakolni és hamarosan le is fagyott. A mag órajelét 1020-ra tettem, így nagyon keveset fogyaszt(falban mérve az egész gép 80w körül). Az így elért maximális Mh/s-om, 14,2 körül van. Így szépen pöfög, 55 fokon, auto-ra állítva a ventit.
A probléma: mivel még mindig kezdőnek számítok, mindezek a beállítások után néztem meg egy videót, amelyben szó volt a HWINFO nevű programról. Letöltöttem én is és azt tapasztaltam, hogy kegyetlen sok memory errort ad így a kártyám. Az lenne a kérdésem, hogy lehet e valamilyen probléma ebből ha így járatom, meghibásodik e a kártya. Mert ha lejjebb veszem a ram frekvenciát, addig, hogy minimális error legyen(óránként 1-2), kb 13,2 Mh/s-ra esik vissza a sebesség.
Annyit még hozzátennék, hogy 1020/2040-es beállításon nincs "rejected share"-em.

zsombor1

Idézetet írta: zsombor1 Dátum március 27, 2018, 12:01:17 DÉLELŐTT
RX560-as kártya.
Bios moddolva.
Eleinte kerestem itt a fórumon és a videósoknál is, hogy milyen értékeket állítsak be. Rájöttem, hogy ezt mindenkinek saját magának kell kitapasztalnia, hogy mit bír a kártyája. Elkezdtem szépen lassan emelni a Mhz-et, és 2040-ig jutottam el úgy, hogy nem fagyott le a gép. Ha már 2050-re emeltem, elkezdett vacakolni és hamarosan le is fagyott. A mag órajelét 1020-ra tettem, így nagyon keveset fogyaszt(falban mérve az egész gép 80w körül). Az így elért maximális Mh/s-om, 14,2 körül van. Így szépen pöfög, 55 fokon, auto-ra állítva a ventit.
A probléma: mivel még mindig kezdőnek számítok, mindezek a beállítások után néztem meg egy videót, amelyben szó volt a HWINFO nevű programról. Letöltöttem én is és azt tapasztaltam, hogy kegyetlen sok memory errort ad így a kártyám. Az lenne a kérdésem, hogy lehet e valamilyen probléma ebből ha így járatom, meghibásodik e a kártya. Mert ha lejjebb veszem a ram frekvenciát, addig, hogy minimális error legyen(óránként 1-2), kb 13,2 Mh/s-ra esik vissza a sebesség.
Annyit még hozzátennék, hogy 1020/2040-es beállításon nincs "rejected share"-em.

Látom most sok szakértő van a cseten, hátha tud valaki a kérdésemre válaszolni. Tehát ha sok a mem error, károsodhat a kártyám?

Székely Vegán

Idézetet írta: zsombor1 Dátum március 28, 2018, 09:25:18 DÉLELŐTT
Idézetet írta: zsombor1 Dátum március 27, 2018, 12:01:17 DÉLELŐTT
RX560-as kártya.
Bios moddolva.
Eleinte kerestem itt a fórumon és a videósoknál is, hogy milyen értékeket állítsak be. Rájöttem, hogy ezt mindenkinek saját magának kell kitapasztalnia, hogy mit bír a kártyája. Elkezdtem szépen lassan emelni a Mhz-et, és 2040-ig jutottam el úgy, hogy nem fagyott le a gép. Ha már 2050-re emeltem, elkezdett vacakolni és hamarosan le is fagyott. A mag órajelét 1020-ra tettem, így nagyon keveset fogyaszt(falban mérve az egész gép 80w körül). Az így elért maximális Mh/s-om, 14,2 körül van. Így szépen pöfög, 55 fokon, auto-ra állítva a ventit.
A probléma: mivel még mindig kezdőnek számítok, mindezek a beállítások után néztem meg egy videót, amelyben szó volt a HWINFO nevű programról. Letöltöttem én is és azt tapasztaltam, hogy kegyetlen sok memory errort ad így a kártyám. Az lenne a kérdésem, hogy lehet e valamilyen probléma ebből ha így járatom, meghibásodik e a kártya. Mert ha lejjebb veszem a ram frekvenciát, addig, hogy minimális error legyen(óránként 1-2), kb 13,2 Mh/s-ra esik vissza a sebesség.
Annyit még hozzátennék, hogy 1020/2040-es beállításon nincs "rejected share"-em.

Látom most sok szakértő van a cseten, hátha tud valaki a kérdésemre válaszolni. Tehát ha sok a mem error, károsodhat a kártyám?


Nem, csak gyengébben fog teljesíteni a pool felé.
***BÁNYÁSZ ÉS KRIPTOPÉNZ VIDEÓIM***
https://www.youtube.com/channel/UC1l3y27zXgQqIumFnzIl0FQ

evko81

hello!


rx 470 armor oc...
Biost 1 éve moddoltam, ugye változott a bios mérete... Ha jól emlékszem, felére csökkent moddolás után..
Na most, nincs meg hirtelen az eredeti bios, de gonodlom, le tudom tölteni több helyről is... megfelelő versiont megkeresem és mehet rá, ugye?


Kérdés, most ugye fele akkora van rajta.... Ha az eredeti dupla biost ráteszem, menni fog? :) Szóval, nem kell más, csak feltolnom rá az eredeti biost?


Köszi